Tag Archives: Tree Pruning Service Cloverleaf

Tree Trimming Cloverleaf

Is it time to call a tree service in Cloverleaf to remove that old tree? It can be a painful choice to make, but sometimes the tree gets too close to the house, gets too diseased, gets an incurable infestation of some pest, or grows too tall and gets close to a power line. If any of these things occur, its best to do the right thing and get rid of the tree. Although you might have spent hours and hours getting the tree to where it is today, it is almost dishonorable to the tree to allow it to suffer in bad conditions.

Our tree removal service will plan it out, climb up the tree and tie two long ropes near the top. Anchor them on the opposite side of the one that we want it to fall towards. This will allow us to adjust the direction the tree is being lowered in, just in case it starts leaning towards anything it could destroy.

Call Us Now for a Free Quote on Tree Removal, Tree Topping, Tree Pruning and Stump Removal.

Call Now (832) 900-4016

Once the tree is down, stump removal can be slightly more difficult. We have several choices; use a stump chipper that will completely destroy the visible section of the stump. Or we can dig it out. Digging out the stump is much more thorough, but takes time. You can choose to do this yourself or have the family help. If you have kids this shouldn’t be a problem. Kids often find the thought of digging fun, and are excited to go outside and dig all day long with their friends.

Tree Stump Killer

Actual Estimates on Tree and Stump Removal Cost

You may not want to wait for stump removal...

There have been some big storms lately throughout New Jersey, most notably Hurricane Sandy. These storms have done significant damage. In the northern part of the state, this has resulted in many broken and downed trees, leaving homeowners to try to figure out what to do with the mess that has been left behind. Should stumps and trees be cleared out right away, or is it okay to leave them behind for a little while?

It may seem like something that can wait for later, but you really may want to work on your yard sooner than later. Leaving dead trees and stumps in your yard can actually cause problems. Here are two issues you may want to think through:

1. Remove Dead Wood for the Sake of Your House

Dead wood in the form of trees, tree stumps, and even stacks of cut wood can become homes for rodents or insects. There may not be a problem right away, but the longer these are left out, the bigger the chance that you may have some uninvited guests move in. This could cause trees to become weaker and fall, or if the wood is too close to the dwelling, could invite termites or carpenter ants right into your house. It's really not worth the risk. If you know you may want to cut your trees down at some point, you might as well do it now.

2. Remove Dead Trees for Safety

Dead trees are not safe. The longer a dead tree sits, the greater the chance it has of falling as roots dry up and the trunk becomes more brittle. Trees that have lost too much off the top will also quickly die. Leaving these trees up for extended periods of time invites a hazard - and can have consequences for persons and property.

How Much Will This Cost?

This can vary greatly depending on the size of the trees and stumps, as well as the number. We can tell you that it's a good idea to get a couple of estimates before taking on a project. Most reputable companies will offer free quotes on project. You will see a great variety in prices, so make sure you get a few quotes. You can find websites, that specialize in things like outsourcing tree stump removal at a discount or use websites like the BBB to find a good fit. Due to the current high demand, there is also a wait for many companies, so you'll have to balance out efficiency and expediency. Ideally, you can get both - and those companies are out there if you look for them.

 

Call Us Now for a Free Quote on Tree Removal, Tree Topping, Tree Pruning and Stump Removal in Cloverleaf.

Call Now (832) 900-4016

Tree And Stump Removal

Positive Approaches on Tree Removal Costs

Thought this article might be interesting about what all is involved in preparing for a tree service job.

I have been running a tree service company for 10 years in Bellingham WA.

The first duty being asked about is the rope and saddle. I use the Buckingham Economy Saddle. On the right side of the saddle I have a Petzl Macrograbber for flipline adjusting. It is secured to the Buckingham saddle with a 5/8ths galvanized shackle.

Also on the right side of the Buckingham saddle I have a three foot lanyard with an autolocking steel clip hard spliced into the end to secure the chainsaw.

On the left side of the Buckingham saddle, I clip a lowering rope and a repelling rope onto the lightweight ring toward the back of the saddle. I use a locking Petzl William Carabiner Tri-Act Gate for the repelling rope.

I am constantly on the look-out for frayed or damaged spots on the repelling rope. I prefer a thicker repelling rope. The ½ Arbor-Plex works well.

The lowering rope I use is determined by the application. Most of the work I do is close quarters and requires lowering of branches and rounds. The lowering ropes vary in length from 150' to 300'.

On the left side of the Buckingham there is a small clip. I carry a Fanno 22" Hand saw. This is used for pruning small branches as I ascend and also as a catch device on situations where I need that extra reach to grab the flipline whipped around the tree.

Other devices on the Buckingham include:

Standard figure 8 for repelling and potential maneuvers while in the tree.

I like to carry a 10' rope flipline with a Prusik hitch. This allows for extra stabilizing before making cuts. It also allows for quick attachment as I ascend through branches, keeping me tied in at all times.

On the left side small ring I have attached a small line that has a wedge secured on it.

The next duty asked to describe on the application is the lift truck operation.

I have owned a 1963 55' Ford High Ranger for four years. First I check all fluids. Brake, oil, transmission, and radiator. As well as the hydraulic tank reservoir. Then I start the engine and do a visual inspection of the engine. I do a visual inspection on the tires and check all the lights for proper working order.

Then I engage the main hydraulic level in the cab and begin to inspect for any broken or damaged hydraulic lines. I lower the outriggers to insure smooth operation. I operate the boom from a manual position on the deck, and then climb into the bucket to test the working order of the bucket hydraulic controls.

I follow all guidelines outlined in the American National Standards manual for Arboricultural Operation/ ANSI Z133.1 Section Aerial Devices. Briefly explained:

I am aware of:

Load capacities of the boom, I set wheel chocks if the wheels are on the ground after lowering the outriggers, I constantly scan in the direction I am travelling, I set up for proper traffic clearances, I maintain proper distance for electrical lines, lift branches off lines with pull ropes before cutting, insure area below before releasing branches to the ground, and constantly monitor for any potential danger.

I operated at this level with the High Ranger for two years. 90% of the tree removals that I do I have to climb. I decided that for me and my business the cost of maintaining the truck was not necessary. I use the bucket truck on my personal property but do not currently use it for my tree service.

Operation of brush chippers:

I have thousands of hours of brush chipping experience. The key to efficient chipping is proper staging of the branches. Cedars are the most difficult. On branches that have multiple smaller branches coming off of the main branch I trim them off. It's easier not to fight the branches when stacking and then feeding into the chipper.

Even when pulling the tree over with bull rope, as soon as the back cut is deep enough I will place my first wedge and hammer it in with a small sledge hammer. This helps to get the tree moving in the desired direction, prevents set back if the rope becomes slack, and helps to keep the chain for binding.

The are many techniques for felling trees. The basic is a face cut, no more than a third way through the tree. When cutting for money I use a humbolt cut, but they take a little more time to do and are not necessary for fire wood applications, so I'll use a conventional face cut on most. As your finishing the depth of the face cut you want to check the gun. There is a small raised mark on chainsaws that allow you to aim the face cut to the desired fall line. With that mark lined up and a straight back cut the tree will grab hold of the hinge wood and cause the tree to follow the desired fall line. There are so many factors involved, and each tree is different.

Proper limbing techniques are important to know for both safety reasons and from keeping the saw from getting pinched. You can lead the branch in the direction you desire by following the same procedure as felling a tree. If you need the branch to drop parallel to the ground you place a cut under the branch and then at full speed place the saw above that cut and go hard. The branch will snap and float down. One way to get the branch to land at the base of the tree is to cut from the top and let the branch break swing down but still be attached. Then make removing cut to send it right next to the tree.

When limbing on the ground you want to be aware of the branch and if there is any tension that would cause it to pop and sling back when you cut it off. I like to start at the top before cutting the main pieces to the ground. I'll go about 10, good size for the chipper and start cutting the limbs off from there. Working my way every 10' till all the branches are off the top.

Bucking large wood is easy if you use a wedge. A peavey or cant hook is used to turn larger logs over. I cut down as far as possible before rolling. Work on the upside of the log. When dropping the last 20' I like to put small long branches in front of the stump coming off. This keeps it off the ground and makes cutting the larger diameter trunks easier. I do the same as I drop major branches onto the ground if possible. Use the dogs to dig into the tree. It's safer than having the chain operation by your feet and cuts into the wood faster.

I subscribe to Arborage, it's a monthly magazine about the tree industry. It talks about the latest equipment and some tree care issues. I use my Western Garden book if there is a particular fruit tree that I need better understanding of how to prune. I do still look over The Fundamentals of General Tree Work. Now with the advent of YouTube, I invest time looking at other peoples techniques to see what I may learn.

Learning for me never stops.

Tim Bento

Stump Cutter

Tree Removal Cost - Determining Factors and Estimates

If you need to remove a tree from your yard for any reason, whether it is unhealthy and likely to fall or simply blocking your view, it is always recommended that you hire a professional for this task. Attempting to remove a tree on your own is very dangerous, and can easily lead to personal injury, electrical shock, or property damage.

When choosing a tree removal company, it is important to choose an experienced, reputable company. Do not trust your property with a company that cuts costs by cutting corners. Know what to look for in a tree service professional to ensure that you are getting the best value for your money.

  • Fully Licensed and Insured. If you hire a company that is not insured, you are asking for a lawsuit. If anything goes wrong or a worker is injured while working on your property, you can be held liable. Although an insured company may charge a little more to cover the insurance, you will not have to worry about hefty legal fees in the case of an accident.

  • Training and Equipment. It takes more than a truck and a chainsaw to properly remove a tree. The best tree removal professionals are fully trained and equipped for any job, whether they are simply trimming a few branches or brining in a crane to remove a large tree.

  • Stump Grinding. If a company does not have the proper equipment to remove and grind the tree's stump, you could be left with unsightly stumps dotting your yard. When you are speaking to tree removal companies, ask them if they will grind the stumps when they are finished removing the tree. Many companies will provide this service at no additional charge.

  • Good Reputation. When you are considering different companies, it helps to hear what others have to say. Look online at various customer review sites to see what previous customers have said about their experiences with the tree removal companies in your area. It is normal to have one or two negative reviews, but if you are consistently seeing more horror stories than praise, it is time to move on. Look for a company that is praised by past customers for professionalism, service, and excellent results.

A diseased or dying tree is a safety hazard, and you should not delay in having one removed from your yard. However, do not rush into a decision by hiring the cheapest tree removal company you can find. Always do business with companies that are fully licensed and insured and known for their professionalism and quality work. Taking the time to choose the right company will provide a much better experience in the long run.

Call Us Now for a Free Quote on Tree Removal, Tree Topping, Tree Pruning and Stump Removal.

Call Now (832) 900-4016


TX

Categories

Get a Free Quote

Contact Form

Tree Trimming Cloverleaf

Contact Us

Kanshoh Trees
5161 San Felipe Street Ste 320, Houston, Texas, 77056

Call Us: (832) 900-4016
http://www.kanshohtrees.com/

Address